Complete Stage 1

Description

• Welded Powder Coated Cabin Frame with Skids, Installed Exterior Sheet Metal with Bubble & Door Frames
• Ground Wheel Kit Including: Axles, Wheels, Tubes & All Hardware Needed for Installation
• Composite Instrument Pod ( Narrow or Wide based on Analog or iEFIS System
• Cabin Enclosure Kit Including: Aluminum & Hinges, Door Handle, Latch & Knobs & All Hardware Needed for Installation
• Complete Analog Instrument & Electrical Kit Including: Solenoid Board, All Gauges Are Plug & Play Wired, Quad CHT Kit with Senders, Quad Engine Oil Temp/Trans Temp/ Oil Pressure/Amp with Senders, Quad Fuel Level/Airtemp/Carbtemp with Senders, Dual Engine Rotor Tach with Senders & Alarms, Manifold Pressure Gauge with Fittings, Tubing & Light Kit, Airspped Indicator with Tubing, Pitot Tube & Light Kit, Altimeter & Vertical Airspeed Gauge With Light Kit,Piper Socket Plug, Hobb’s Hour Meter, 12V Outlet,10° Bank Indicator, 5 & 10 Amp Breakers, Chip Detectors, All Hardware Needed for Installation. Lighting Kit Including: Strobe, MicroBurst Nav & Taillight, Landing Light & All Hardware Needed For Installation
• Complete iEFIS Instrument & Electrical Kit Including: Solenoid Board, iEFIS Challenger, iBox ASI, Magnetometer, XF 12 Thermocouple Channel, iBox CAN Bus Harness iBox, CHT, Bayonet,Thermocouple Cable, EGT Thermo, Westach Oil Temp Sender, Oil Pressure Sender, Water/Oil Temperature Sender, 24″ Fuel Level Sender, UMA Tach Sending Unit, Carb Temp Sender,Oil Pressure Switch, Pitot Tube, 12V Outlet, Chip Dectors, iEFIS Backup Battery, Magneto Switch, 5,10 & 25 Amp Breakers, Piper Socket Plug, Hobb’s Meter, 12V Outlet,10° Bank Indicator, 5 & 10 Amp Breakers, Chip Detectors, All Hardware Needed for Installation. Lighting Kit Including: Strobe, MicroBurst Nav & Taillight, Landing Light & All Hardware Needed For Installation
• COMPLETE FLIGHT CONTROL KIT INCLUDING: Throttle Linkage Rodends with Nuts, Control Rodends with Nuts, Powder Coated Cyclic Lock, Cyclic Pistol Grip With Switches, Collective Rubber Grips With Chrome Trim, Carburetor Mixture Plate Arm, Bell Crank Arm With Hardware, Push Button Cables, Plated Curved Cyclic Sticks, 3/4 Clamp Collars, 1/4 Clamp Collar, Collective Trim Hardware, Tail Rotor Control Includes: Push-Pull Cable, Rodend & All Hardware For Installation
• Complete Electric Trim Kit Including: Relay Box With Hardware, Trim Wire Harness, Pitch Motor Mount,Motor,Drum & Cable With Hardware, Pitch Control Rod, Roll Motor Mount, Motor,Drum & Cable With Hardware
• Complete Governor Kit Including: Control Box, Connecting Rod, Rod End & Nut, Stepper Motor, Poly Clutch With Arm & Hardware, Motor Mount With Hardware, Mag Sensor (Only Needed For Impulse Mags), Governor Wiring Harness
• Complete Collective Friction Kit Including: Friction Blocks & Plates, Knob, Threaded Control Rod & All Hardware For Installation
• Complete Collective Switch Box Kit Analog/ iEFIS Including: Collective Switch Box Machined, All Switches To Be Installed In Switch Box, Face Plate & All Hardware For Installation
• Complete Fuselage Finish Kit Including: Skid Caps, Welded Ballast Assembly & Pin, Tube Seal, Fitting for Air Pressure Test Inlet, Safari FootPedals & Hardware, Bulk Fasteners Kit, Bonus Pack Fasteners Kit
• Raw Materials (Stage 1) Incuding: 5/16″ Tubing For Doors, Lexan For Doors, Aluminum Angle, Aluminum Tubing For Controls, Aluminum Sheet .032″, Aluminum Sheet .063″